If your home sits where California’s forests meet neighborhoods, wildfire risk can depend on details as small as a single tree. On November 18, 2026, NASA published an announcement about a 3D map of the entire state at one square meter per pixel. The statewide lidar datasets were first publicly released on December 12, 2025. That release included 10-meter and 30-meter products covering all of California, with 1-meter data available in select areas.
The NASA 3D wildfire map of California can show individual trees. That detail could matter when planners judge how close fuel sits to homes.
NASA’s Wildfire, Ecosystem Resilience, and Risk Assessment Initiative produced the maps, with researchers at NASA’s Ames Research Center in California. The team used airborne lidar, a technology that uses a pulsed laser to measure distances. It combined that data with data from the U.S. Geological Survey’s 3D Elevation Program. The result is a consistent statewide map of all of California. Each pixel, the small square unit that makes up the map, covers one square meter, or about 1.2 square yards. NASA, the U.S. space agency, worked on the maps with the California Natural Resources Agency and the California Air Resources Board as partners.
For a homeowner, the practical change is a view of the land around a house at the scale of single trees. NASA says most space-based lidar data has a resolution of 10 to 25 square meters per pixel. This suggests that at that coarser scale, it is harder to tell one tree from its neighbor. That level of detail could help inform decisions about which trees to thin or clear near a home.
How the NASA 3D Wildfire Map of California Was Built
The map combines two sources. Airborne lidar sends out laser pulses and measures how long they take to return. That timing gives precise distances to the ground and to the tops of trees. The team combined this data with data collected by the U.S. Geological Survey’s 3D Elevation Program to create a consistent statewide map. The returns form a 3D point cloud, a dense set of measured points that software turns into a model of the land and its vegetation.
One lidar image in the release shows a wildland-urban interface in Santa Clara County, California. That is the zone where homes and other development meet or intermingle with wildland vegetation. The image was acquired in 2020.
NASA worked in collaboration with the California Natural Resources Agency and the California Air Resources Board. NASA says the team hopes to use these maps to develop products that help assess wildfire risk. The release also names protecting wildlife and ecosystems and managing natural resources as goals. The lidar dataset is available through NASA Earthdata, the agency’s public catalog of Earth science data. For another California environmental story built on measurable scale, read Salton Sea Restoration Hits 2,000 Acres as East Pond Expansion Triggers Next 9,000-Acre Phase.
Going from 10 to 25 square meters per pixel down to one square meter changes what a statewide map can show. At one square meter per pixel, the map can show individual trees alongside the surrounding forest. The same statewide dataset can be examined at both county and single-property scales.
How detailed are NASA’s 3D wildfire maps of California?
The maps show one square meter, about 1.2 square yards, per pixel. NASA says that is detailed enough to show down to the scale of a single tree. Most space-based lidar data has a resolution of 10 to 25 square meters per pixel, which is far coarser than the new maps.
How does airborne lidar differ from satellite lidar for wildfire risk?
Lidar measures distance by timing laser pulses that bounce back from surfaces such as the ground and vegetation. Airborne lidar carries that sensor on an aircraft. NASA’s comparison focuses on resolution: most space-based lidar data has 10 to 25 square meters per pixel, while the California maps use one square meter. Finer pixels generally make single trees and nearby vegetation easier to separate.
Which California agencies partnered with NASA on the 3D maps?
NASA worked in collaboration with the California Natural Resources Agency and the California Air Resources Board. The map also uses data collected by the U.S. Geological Survey’s 3D Elevation Program. The work was carried out by NASA’s Wildfire, Ecosystem Resilience, and Risk Assessment Initiative, with researchers at NASA’s Ames Research Center.
NASA’s statewide map covers all of California at one square meter per pixel, enough to show single trees. The California Natural Resources Agency and the California Air Resources Board worked with NASA on the project. You can read NASA’s full announcement or view the lidar dataset on NASA Earthdata. For a broader look at how California cities measure environmental progress, see America’s Greenest Cities: 2025 Rankings Based on 28 Environmental Metrics.